Inner gears, 3 synchromesh with baulk ring, B-type, September 1964 up to September 1968
Gearbox, 19 teeth
848 cc & 998 cc
Required: 1
Gearbox, 20 teeth
some Cooper & S
Required: 1
first motion shaft
outer diameter: 62.5 mm
Required: 1
0.096 mm, ball bearing 1st motion shaft
replaced by 467566
Required: 1
0.098 mm, ball bearing 1st motion shaft
Required: 1
1st motion drive, 24 teeth
Required: 1
for mainshaft end in 1st motion shaft, open cage
Required: 1
Required: 1
in synchro hub assy
Diameter: 7/32" (5.556 mm)
Required: 3
for 3rd gear
Required: 1
for 2nd and 3rd gear on mainshaft
Required: 2
3rd speed, 23 teeth
848 cc & 998 cc
for laygear 215792
Required: 1
3rd speed, 24 teeth
Cooper S only
for laygear 1175
Required: 1
for locating washer 2nd gear
Required: 2
2nd speed, 28 teeth
Required: 1
1st gear, with 2nd gear synchronizer assembly
Required: 1
in synchro hub assy
Diameter: 7/32" (5.556 mm)
Required: 3
Double ball, Gearbox mainshaft
outer diameter: 65 mm
Required: 1
as stop in gearbox casing
for gearbox main bearing 215940
Required: 1
for laygear- and reverse shaft
Required: 1
for gearbox main bearing, cast iron, 4 hole fitting
Required: 1
17 teeth, final drive 3.76.1
more final drives
Required: 1
18 teeth, final drive 3.44.1
1275 cc, late 998 cc
more final drives
Required: 1
Laygear, large - 0,123" to 0.124"
as requiered
Laygear, large - 0.125" to 0.126"
as requiered
Laygear, large - 0.127" to 0.128"
as requiered
Laygear, large - 0.130" to 0.131"
as requiered
for needlebearing in laygear
Required: 1
teeth: 28/24/19/13
848 cc & 998 cc
Required: 1
teeth: 26/23/19/13. This corresponds to the following ratio: 3.2:1, 1.916:1, 1.357:1 and 1:1
1275 cc Cooper S
Required: 1
reverse speed
alternative use A-type gear 215872, identical but without oilgroove on thrust side
Required: 1
for reverse gear
Required: 1
Primary drive, 31 teeth, shaft size: 0.750" (19 mm)
equal shaft length
Required: 1
Idler gear, 0.130"- 0.131"
green coding, as requiered
Required: 2
Idler gear, 0.132"- 0.133"
black coding, as required
Required: 2
Idler gear, 0.134"- 0.135"
white coding, as requiered
Required: 2
Idler gear, 0.136"- 0.137"
blue coding, as requiered
Required: 2
Idler gear, 0.138"- 0.139"
red coding, as requiered
Required: 2
for idler gear
outer diameter: 1.004" (25.5 mm)
Required: 2
Gearbox side
for needle bearing 203708
Required: 1
1.1/8", 1/2" drive, for nut main shaft 1st motion
more workshop tools
Required: 1
with 1.1/2" AF (38 mm) spanner size. 1/2" square drive socket with 37 mm internal depth and 80 mm total height. For Austin Healey ball joints and many other applications
more workshop tools
Required: 1
