Fittings bulkhead Series II an IIA
for controls
Series II, IIA petrol-models to vehicle suffix "C" (to September 1965)
Required: 1
for controls
Series II, IIA diesel-models to vehicle suffix "C" (to September 1965)
Required: 1
retaining support panel
Series II, IIA diesel-models to vehicle suffix "C" (to September 1965)
Required: 6
retaining support panel
Series II, IIA diesel-models to vehicle suffix "C" (to September 1965)
Required: 6
retaining support panel
Series II, IIA diesel-models to vehicle suffix "C" (to September 1965)
Required: 6
retaining support panel
Series II, IIA diesel-models to vehicle suffix "C" (to September 1965)
Required: 3
retaining finisher
Required: 2
cutout accelerator pedal
Required: 1
clutch or brake pedal hole
Required: 1
dip switch hole
Series II (1958 to 1959)
Required: 1
retaining blanking plate
Series II (1958 to 1959)
Required: 2
retaining blanking plate
Series II (1958 to 1959)
Required: 2
retaining blanking plate
Series II (1958 to 1959)
Required: 2
voltage regulator
Series II
Required: 1
retaining mounting bracket
Series II
Required: 2
retaining mounting bracket
Series II
Required: 1
retaining mounting bracket
Series II
Required: 1
fixing bulkhead to chassis frame
Required: 4
retaining hinge to ventilatior flap
Vehicles with hinges fixed by screws and nuts
Required: 8
retaining hinge to ventilatior flap
Vehicles with hinges fixed by screws and nuts
Required: 8
retaining hinge to ventilatior flap
Vehicles with hinges fixed by screws and nuts
Required: 16
retaining hinge to ventilatior flap
Vehicles with hinges fixed by screws and nuts
Required: 8
- LH
Vehicles with hinges fixed by screws and nuts
Required: 1
below windscreen, LH side
Vehicles with welded hinges
Required: 1
- RH
Vehicles with hinges fixed by screws and nuts
Required: 1
below windscreen, RH side
Vehicles with welded hinges
Required: 1
air flap
Required: 2
retaining operating lever
Required: 4
fixing windscreen to bulkhead
Required: 4
windscreen frame bracket - galvanized variant with 5/16" UNF thread
Required: 2
for windscreen frame bracket - variant with plastic cap and 5/16" UNF thread
Required: 2
windscreen frame bracket - brass variant with 5/16" UNF thread
Required: 2
retaining bracket windscreen to bulkhead
Required: 4
retaining bracket windscreen to bulkhead
Required: 4
retaining bracket windscreen to bulkhead
Required: 4
retaining check arm to mounting bracket
Required: 4
retaining check arm to mounting bracket
Required: 2
retaining check arm to mounting bracket
Required: 2
check arm, RH
Required: 1
check arm, LH
Required: 1
retaining check arm to front door
Required: 4
retaining check arm to front door
Required: 2
for bulkhead support with 5/16"UNF thread
Vehicles with vehicle suffix "A"
Required: 1
for bulkhead support with 3/8" UNF thread
Vehicles from vehicle suffix "B"
Required: 1
with 5/16"UNF thread
Vehicles with vehicle suffix "A"
Required: 1
with 3/8" UNF thread
Vehicles from vehicle suffix "B"
Required: 1
for 5/16"UNF thread
Vehicles with vehicle suffix "A"
Required: 1
for 3/8" UNF thread
Vehicles from vehicle suffix "B"
Required: 1
with 5/16"UNF thread
Vehicles with vehicle suffix "A"
Required: 1
with 3/8" UNF thread
Vehicles from vehicle suffix "B"
Required: 1
fixing steady rod to bulkhead - BSF thread
Required: 1
fixing steady rod to bulkhead - UNF thread
Required: 1
