Brake controls
replacement for single line brakes with Dunlop cylinder. Characteristic: 7/8" bore size
Mark II (1959-65): 2.4 to 121081 and 28155, 3.4 to 171379 and 180813, 3.8 to 235262 and 224653
Required: 1
replacement for single line brakes with Girling cylinder. Characteristic: 7/8" bore size
Mark II (1965-69): 2.4 from 121082 and 128156, 3.4 from 171380 and 180814, 3.8 from 235263 and 224654 plus all 240 and 340 models
Required: 1
for original Dunlop cylinder with 7/8" bore
2.4 RHD models to 121081, 12.4 LHD models to 28155, 3.4 RHD models to 171379, 3.4 LHD models to 180813, 3.8 RHD models to 235262, 3.8 LHD models to 224653
Required: 1
for original Dunlop cylinder with 7/8" bore aftermarket
2.4 RHD models to 121081, 12.4 LHD models to 28155, 3.4 RHD models to 171379, 3.4 LHD models to 180813, 3.8 RHD models to 235262, 3.8 LHD models to 224653
Required: 1
for Girling type cylinder with 7/8" bore
2.4 RHD models from 121082, 2.4 LHD models from 128156, 3.4 RHD models from 171380, 3.4 LHD models from 180814, 3.8 RHD models from 235263, 3.8 LHD models from 224654, all 240 and 340 models
Required: 1
brake master cylinder
Mark II (1965-69): 3.4 from 171380 (RHD) and 180814 (LHD), 3.8 from 235263 (RHD) and 224654 (LHD) plus all 340 models
Required: 1
brake master cylinder
Required: 2
for brake fluid reservoir
For new type cap
Required: 1
from brake fluid reservoir to hydraulic pipe
Required: 1
Marked with P.F.D. with yellow band
Required: 1
reconditioned, in exchange
Required: 1
brake pressure: 3:1, diameter: 5/8". May replace the genuine Girling brake servo
213946 was never originally used of any of the Mark II models. If may however be fitted satisfactorily by making small alterations to the inner wing panel and by modifying the mounting method.
Required: 1
for original Girling brake servo - services vaccum side
Required: 1
for original Girling brake servo - services fluid side
Required: 1
air control valve
Required: 1
from non-return valve to brake servo
Required: 1
from non-return valve to servo pipe in inlet manifold
Required: 1
stainless steel braided, set with 3 lines
Required: 2
stainless steel braided, set with 3 lines
Required: 1
3/8" x 24 UNF - for 3/16" pipe
Required: 1
at joint of hose to 3-way connector
Required: 1
with 'J' for Jaguar
Manual and overdrive
Required: 1
brake pedal - variant with 'J' for Jaguar
Cars with automatic transmission
Required: 1
brake pedal
Required: 2
on bolt fixing shaft supporting brake pedal in housing
Required: 1
5 way type
with connection for switch
Required: 1
for RHD models with manual transmission
Mark II 2.4 (1959-66)
Required: 1
for RHD models with automatic transmission
Mark II 2.4 to 1966
Required: 1
for RHD models with manual transmission
Mark II 2.4 and 240 from 1966
Required: 1
for RHD models with automatic transmission
Mark II 2.4 and 240 from 1966
Required: 1
for RHD models with manual transmission
Mark II 3.4 and 3.8 to 1966
Required: 1
for RHD models with automatic transmission
Mark II 3.4 and 3.8 to 1966
Required: 1
for RHD models with manual transmission
Mark II 3.4, 3.8 and 340 from 1966
Required: 1
for RHD models with automatic transmission
Mark II 3.4, 3.8 and 340 from 1966
Required: 1
for LHD models with manual transmission
Mark II 2.4 to 1966
Required: 1
for LHD models with automatic transmission
Mark II 2.4 to 1966
Required: 1
for LHD models with manual transmission
Mark II 2.4 and 240 from 1966
Required: 1
for LHD models with automatic transmission
Mark II 2.4 and 240 from 1966
Required: 1
for LHD models with manual transmission
Mark II 3.4 and 3.8 to 1966
Required: 1
for RHD models with automatic transmission
Mark II 3.4 and 3.8 to 1966
Required: 1
for LHD models with manual transmission
Mark II (1965-69): 3.4 from 180814, 3.8 from 224654 plus all 240 and 340 models
Required: 1
for LHD models with automatic transmission
Mark II (1965-69): 3.4 from 180814, 3.8 from 224654 plus all 240 and 340 models
Required: 1
with 3/16" diameter. 25 ft coil made from top quality copper and copper nickel tubing
Required: 1
brake fluid reservoir. Metal replacement
Required: 1
brake fluid reservoir - high quality aftermarket product with black cap
Required: 1
brake servo
2.4, 3.4, 3.8 plus 240 and 340 (1959-69)
Required: 1
