External electrics and wiring harnesses
with 7" diameter. Light unit with clear lens, curved glass and E marking. Fits to RHD models without pilot
Required: 2
with 7" diameter. Light unit with clear lens, curved glass and E marking. Fits to LHD models without pilot
Required: 2
for RHD models. 12 volt, 50/40 watt, P36D British pre-focus base, clear bulb surface
Required: 2
for LHD models. 12 volt, 50/40 watt, P36D British pre-focus base, clear bulb surface
Required: 2
for BPF bulbs, with Lucar terminals for harness 6486
Required: 2
with 7" diameter variant, without pilot for LHD cars. Supplied in pairs
Required: 1
with 7" diameter, variant with pilot for LHD cars. Supplied in pairs
Required: 1
with 7" diameter. Light unit with clear lens, curved glass and E marking. Fits to RHD models without pilot and sold as a pair
Required: 1
with 7" diameter. Light unit with clear lens, curved glass and E marking. Fits to RHD models with pilot and sold as a pair
Required: 1
PL700 type with clear, curved lens. 7" version without pilot for RHD models. These headlamps look period correct but are only compatible with H4 bulbs
Use bulb 3496
Required: 2
'J light' type, without pilot - 7" diameter
Required: 2
with clear lens and built-in 65/55 watt bulb, RHD, no pilot - 7" diameter
Required: 2
with clear lens and built-in 60/35 watt bulb, LHD, no pilot - 7" diameter
Required: 2
R/H, Flat lense
Early cars only
Required: 2
for 7" headlamp - chromed clip-on type for headlamp bowl with 2 adjusting screws
Required: 2
for 7" headlamp, complete unit with retaining rim. Metal variant for bowl with 2 adjusters
Required: 2
with 7" diameter, made from plastic. Complete with inner rim, rubber seal and adjuster kit
Required: 2
headlamp chrome rim - narrow type with cutout
Required: 2
headlamp chrome rim - wide type without cutout
Required: 2
for 7" headlamp bowl with 2 adjusting screws
Required: 2
with 7" diameter, made from metal - 2 adjuster variant
Required: 2
12 volt, 45/40 watt
Spade fitting for original type L/H drive headlights
Required: 2
with plug - for H4, Sealed Beam and Bilux headlamps without pilot
To adapt type 410 and sealed beam
Required: 2
side light, fixed on wing - clear glass lens, retained by chrome ring - type: L490
Mark II (1959-69) ? Daimler 250 V8 Saloon (1962-69)
Required: 2
sidelight to housing
Only for vehicles with OE sidelight
Required: 2
sidelight to housing
Only for vehicles with Limora sidelight
Required: 2
12 volt, 5 watt, BA9s bajonett base, clear bulb surface - side lamp
Required: 2
for indicator on front wing - red plastic type
Required: 2
front indicator, amber glass lens, retained by chrome ring - type: L563
Required: 2
front indicator, clear glass lens, retained by chrome ring
Required: 2
and chrome rim, front indicator - amber glass type L563
Required: 2
and chrome rim, front indicator - clear glass type L563
Required: 2
front indicator - amber galss type type L563
Required: 2
front indicator - clear glass type: L563
Required: 2
12 volt, 21 watt, BAY15s bajonett base, clear bulb surface - indicator, rear fog lamp
Required: 2
replica of the FL5 flasher relay with 3 screw-in terminals and round housing
Required: 1
replica of the FL5 flasher relay with 3 Lucar terminals and round housing
Required: 1
FL5 flasher relay with 3 terminals and round housing
Required: 1
'Fogranger', back mounted period style lamp with 5.3/4" diameter. Comes with fluted lens and chromed bowl
Required: 2
12 volt, 48 watt, P36S British pre-focus base, clear bulb surface - fog lamp
Required: 2
for period style fog lamp 'Fogranger' with 5.3/4" diameter
Required: 2
Auxiliary FT11
Required: 2
for 6" fog/spot lamps - chrome
Lucas 576 fog light
Required: 2
for fog and spot lamps with 5.3/4" diameter
Lucas 576 fog light
Required: 2
for 7" fog/spot lamps - chrome
Lucas 700 fog light
Required: 2
for fog/spot lamps upto 7"
Lucas 700 fog light
Required: 2
rear indicator - amber
European models
Required: 2
rear indicator - red
USA models only
Required: 2
stop and tail light in rear lamp - red plastic lens, type: L627
Required: 2
with panhead - 1/4" x No.6
Required: 6
between flasher and rear lamp
Required: 2
12 volt, 21 watt, BAY15s bajonett base, clear bulb surface - indicator, rear fog lamp
Required: 2
12 volt, 21/5 watt, BAY15d bajonet base, clear bulb surface - stop and tail lamp
Required: 2
with spring, double wire - stop/tail
Required: 2
hydraulic switch with lucar terminals and 1/8" x 27 NPTF thread
Required: 1
reverse lamp
Required: 1
number plate lamp
Required: 3
12 volt, 5 watt, BA9s bajonett base, clear bulb surface - number plate lamp
Required: 3
12 volt, 21 watt, BAY15s bajonett base, clear bulb surface - indicator, rear fog lamp
Required: 2
reverse light and overdrive isolation
Required: 1
reverse and number plate lamp - clear plastic type L512
Required: 1
H4 - 12 volt, 60/55 watt, unified European P43t base, clear bulb surface
As original
Required: 2
H4 -12 volt, 60/55 watt, unified European P43t base, clear Xenon bulb surface
Required: 2
H4 - 12 volt, 100/80 watt, unified European POR43t base, clear bulb surface
Required: 2
12 volt, 45/40 watt, unified European P45t base, clear bulb surface
type 410 for original L/H drive headlights (expect France)
Required: 2
for RHD models. 12 volt, 50/40 watt, P36D British pre-focus base, clear bulb surface
type 414 - R/H drive headlights (except France). For later replacement headlights.
Required: 2
for LHD models. 12 volt, 50/40 watt, P36D British pre-focus base, clear bulb surface
type 415 - L/H drive headlights (except France). For later replacement headlights.
Required: 2
12 volt, 5 watt, BA9s bajonett base, clear bulb surface - side lamp, number plate lamp
Sidelight, map light, interior lamp at top of centre pillars, map lamp, Number plate lamp and boot lamp, etc
12 volt, 21 watt, BAY15s bajonett base, clear bulb surface - indicator, rear fog lamp
rear flasher light, reversing light
Required: 3
12 volt, 48 watt, P36S British pre-focus base, clear bulb surface - fog lamp
Fog light
Required: 2
12 volt, 21/5 watt, BAY15d bajonet base, clear bulb surface - stop and tail lamp
Brake and tail light
Required: 2
12 volt, 2.2 watt, E10/13 screw base, clear bulb surface - instrument panel and interior lamp
Headlight warning, ignition warning, fuel warning, choke control warning (2.4 only), manual electric choke warning (not 2.4), hazard warning, heated rear window warning, hadbrake/brake fluid level warning, etc.
12 volt, 2.0 watt, BA7S bajonet base, clear bulb surface - instrument and switch illumination
Flasher indicator warning, indicatorstrip illumination, overdrive indicator, automatic transmission indicator, etc.
6 watt festoon type
Glove box lamp, interior lamp in rear quarters
Required: 3
high note, Lucas HF.1748 type with 2 terminals. 12 volt - reconditioned, in exchange
Required: 1
low note, Lucas HF.1748 type with 2 terminals. 12 volt - reconditioned, in exchange
Required: 1
high note - alloy cast horn with domed cover. 12 volt with 2 wire terminals
Replacement. Not windtone. Not early type
Required: 1
low note - alloy cast horn with domed cover. 12 volt with 2 wire terminals
Replacement. Not windtone. Not early type
Required: 1
earth contact to steering column
Required: 2
Main ???
Manual. Not 240/340
Required: 1
for front famps, fog lamps, side and indicator lamps - variant with PVC cables and taped outer covering
Required: 1
with plug - for H4, Sealed Beam and Bilux headlamps without pilot
No sidelight
Required: 2
interior lamp - variant with PVC cables and taped outer covering
Required: 1
For R/H drive. For L/H drive 13 required. For screen washer tubes, speedometercable, bonnet lock control, screen wiper cable, dipswitch cable, petrol tank cable, boot lid cable, door switches, brake pipes and side lamps.
Required: 12
for terminal insulating on starter motor
Required: 3
Hole for L/H dipswitch cable (R/H drive models only), redundant speedo cable hole in bulkhead, hole for screen washer tubing and redudant cable entry hole in bulkhead.
Required: 4
outer diameter: 40 mm, for 32 mm hole and 4 mm cable
Body harness, and dipswitch on R/H drive
Required: 1
outer diameter: 40 mm, for 32 mm hole and 10 mm cable
Body harness through sills
Required: 4
outer diameter: 53 mm, for 38 mm hole and 32 mm cable
Forward harness
Required: 1
outer diameter: 46 mm, for 29 mm hole and 25 mm cable
At rear of body for body harness
Required: 2
made from rubber with 47 mm outer diameter - for 38 mm hole and 10 mm cable, total height: 7.7 mm
Lamp cables
Required: 2
outer diameter: ?? mm, for 12.7 mm hole and 4 mm cable
In centre pillars
Required: 2
outer diameter: 32 mm, for 19 mm hole and 14 mm cable
Heater control through scuttle
Required: 2
outer diameter: 32 mm, for 19 mm hole and 14 mm cable
Instrument panel wing. Required only with steering column connector cable.
Required: 1
???
Petrol pump. Not included in 315284
Required: 2
transmission cable access hole
Automatic only
Required: 1
Transmission dipstick hole. Automatic only
Required: 1
for wiring loom - supplied in set of 30
Required: 1
for 10 way female connector
On L/H inner wing
Required: 1
for 5 way female connector
On R/H inner wing
Required: 1
