Front suspension MKII and DV8
with inner sleeve, inner position, front upper wishbone
Required: 4
securing upper wishbone levers to fulcrum shafts
Per wishbone
Required: 2
upper wishbone - front suspension
Required: 2
upper wishbone - front suspension
Required: 2
for upper swivel fitted with grease nipple - black
Required: 5
shorter - ball joint to upper wishbone
Per ball joint
Required: 1
longer - ball joint to upper wishbone
Per ball joint
Required: 1
front suspension castor angle - 0.079"
front suspension castor angle - 0.063"
front suspension castor angle - 0.039"
lower wishbone - front suspension
Per wishbone
Required: 4
lower wishbone - front suspension
Required: 4
lower wishbone - front suspension. Variant with inner sleeve
Per wishbone
Required: 2
securing lower wishbone levers to fulcrum shaft
Per wishbone
Required: 2
for lower pin cap
Per ball joint. Use with SJ3146/1
Required: 4
lower wishbone - front suspension
Kit per wishbone. Original type - repro
Required: 2
lower wishbone - front suspension. Modern type, use together with bolt 208080
Required: 2
lower wishbone - front suspension. Modern type, use together with bolt 208080
Required: 2
lower wishbone - front suspension. Modern type, use together with bolt 208080
Required: 2
for lower pin cap
Per ball joint. For original type only
Required: 4
on stub axle
Later type..Quote chassis no.
Required: 2
front suspension - inner bearing
Required: 2
front suspension - outer bearing
Required: 2
at front of front crossmember - aftermarket
Required: 2
at front of front crossmember
Required: 2
securing front mountings to crossmember
Required: 2
at rear of front crossmember - aftermarket
Required: 2
at rear of front crossmember
Required: 2
securing rear mountings to crossmember
Required: 4
front suspension
Mark II 3.4, 3.8 and 340 (1959-69)
Required: 2
fron suspension
Mark II 2.4 and 240 (1959-69) ? Daimler 250 V8 Saloon (1962-69)
Required: 2
securing spring seat to lower wishbone
Required: 10
securing spring to lower wishbone
Not pointed as original
Required: 2
securing shock absorber bracket to spring seat
Required: 8
lower shock absorber mounting bracket - length: 47.7 mm
Required: 2
lower shock absorber mounting bracket - length: 50.8 mm
Required: 2
front shock absorber
Comprises bushes, washers & nuts
Required: 2
outer - with track rod ends assembly. Adjustable type suits both sides
Required: 1
LH side
Required: 1
outer - with track rod ends assembly. Adjustable type suits both sides
Required: 1
RH side
Required: 1
track rod end - made from clear nylon
Required: 2
upper and lower swivel gaiter and track rod end gaiter
Required: 2
and pin for centre steering rod end - standard version
Required: 2
and pin for centre steering rod end - uprated version
Required: 2
securing pin and bush to drop arm & idler lever
Required: 2
centre steering rod, RH side. For vehicles without power assisted steering - reconditioned, in exchange
Required: 1
centre steering rod, LH side. For vehicles without power assisted steering - reconditioned, in exchange
Not power assisted steering. Pin cannot be changed
Required: 1
centre steering rod, RH side. For vehicles with power assisted steering - reconditioned, in exchange
Power assisted steering
Required: 1
centre steering rod, LH side. For vehicles with power assisted steering - reconditioned, in exchange
Power assisted steering
Required: 1
front anti roll bar with 13/16" diameter
Required: 2
at bottom end of anti roll bar link
Required: 4
for anti roll bar bush, outer position with 32 mm outer diameter and 10.3 mm hole diameter
Required: 2
for anti roll bar bush, inner position with 32 mm outer diameter and 11.3 mm hole diameter
Required: 2
centre - complete unit with track rod ends
Required: 1
front suspension
Adjustable, The first step to improving the handling of your Mark II is to fit uprated shock absorbers and, the fitting of either Spax or Koni units is highly recommended. Units are sold individually, but, should be fitted in axle pairs.
Required: 2
upper wishbone, front suspension
Required: 2
