Wishbones, shock absorber and anti roll bar
front - new item. Reproduction with cylindric domed extension
Required: 2
front suspension - original specification without cylindric domed extension, in exchange. Please notice: Only the original shock absorber without this domed extension can be reconditioned. As we can't refurbish the domed shock absorbers, we are not going to take these reproductions in exchange
Required: 2
front suspension - new item. Reproduction with cylindric domed extension and uprated by 30% compared to standard shock absorber
Required: 2
front suspension - original specification without cylindric domed extension, in exchange. Uprated by 30% compared to standard shock absorber. Please notice: Only the original shock absorber without this domed extension can be reconditioned. As we can't refurbish the domed shock absorbers, we are not going to take these reproductions in exchange
Required: 2
front - 25% uprated valve to fit to your own shocks
Required: 2
shock absorber to suspension link trunnion
Required: 2
May replace slotted nut 4834 and split pin 3269
Required: 2
front uspension, upper
Required: 2
shock absorber to suspension link trunnion - barrel type
Required: 4
shock absorber to suspension link trunnion - top hat type
Required: 4
shock absorber to suspension link trunnion
Required: 4
front suspension
BN1 and BN2 (1953-56), BN4 to February 1957 (LHD models to 35706 and RHD models to 35826)
Required: 2
front suspension
BN4 from 35707 (LHD) and from 35827 (RHD) plus all BN6, BN7, BT7, BJ7 and BJ8 (1957-68)
Required: 2
front suspansion - variant with UNF thread
Required: 2
with BSF thread
BN1 - only in connection with the original bump stop
Required: 4
UNF thread
BN1 with bump stop 19066 plus all BN2 to BJ8
Required: 4
LH front and RH rear - new item
BN2 to BJ8 (1955-68)
Required: 2
LH front and RH rear - used item
BN2 to BJ8 (1955-68)
Required: 2
RH front and LH rear - new item
BN2 to BJ8 (1955-68)
Required: 2
RH front and LH rear - used item
BN2 to BJ8 (1955-68)
Required: 2
wishbone to spring pan - length: 2.1/4"
Required: 4
wishbone to spring pan and to anti roll bar - length: 2.1/2"
Required: 4
for fulcrum pin in wishbone - variant with UNF thread
Required: 4
wishbone to chassis frame. With washer and nyloc nut assembly
Contains illustrations 28, 30 and 31
Required: 4
wishbone, inner - original design
Required: 8
wishbone, inner position
Required: 8
front suspension - 5/8" diameter
Original equipment on BN4 to BJ8 (1956-68) - also suitable for BN1 and BN2
Required: 1
front suspension - improved version with 3/4” diameter
BN1 to BJ8 (1953-68)
Required: 1
front suspension - improved version with 7/8" diameter plus fitting kit
BN1 to BJ8 (1953-68)
Required: 1
front anti roll bar - 9/16" diameter
BN1 and BN2 mit originalem Stabilisator (1953-56)
Required: 2
front anti roll bar - 9/16" diameter
BN1 and BN2 mit originalem Stabilisator (1953-56)
Required: 2
front anti roll bar - 5/8" diameter
BN4 to BJ8 (1956-68)
Required: 2
front anti roll bar with 5/8" diameter
BN4 to BJ8 (1956-68)
Required: 2
front anti roll bar - 3/4" diameter
BN1 to BJ8 (1953-68)
Required: 2
front anti roll bar with 3/4" diameter
BN1 to BJ8 (1953-68)
Required: 2
front anti roll bar with 7/8" diameter
BN1 to BJ8 (1953-68)
Required: 2
front and rear anti roll bar bush
Required: 2
anti roll bar to chassis frame
BN1 and BN2 (1953-56)
Required: 4
anti roll bar to chassis frame
BN4 to BJ8 (1956-68)
Required: 4
front suspension. Including rubber bushes, washers and nuts
Required: 2
complete kit for front and rear axle including 4 Bilstein dampers
BN1, BN2, BN4, BN6, BN7, BT7 and BJ7 plus BJ8 to 26704 (1953-64)
Required: 1
complete kit for front and rear axle including 4 Bilstein dampers
Required: 1
with top trunnion fulcrum pin - complete car set. The eccentric fulcrum pin enables you to set the front suspension to negative camber without disassembling.
Required: 1
SAE 20W
Required: 1
Content: 500 ml (?18.00 / 1000 ml)
