Wheel bearings and drive shafts
rear, including large spacer bushing - made in Italy
600 and D 1. Serie (1955-64)
Required: 2
rear, including large spacer bushing - made in Italy
600 D 2. Serise and 3. Series (1964-69)
Required: 2
rear, including large spacer bushing - aftermarket quality
600 D 2. Serie und 3. Serie (1964-69)
Required: 2
rear wheel bearing - height: 32.7 mm
Required: 2
rear wheel bearing - height: 11.3 mm
Required: 2
rear wheel bearing
600 and 600 D 1. Series (1955-64)
Required: 4
rear wheel bearing
600 D 2. Serie and 3. Serie (1964-69)
Required: 4
with hub - identified by coarse toothing
600 and 600 D 1. Series (1955-64) and Multipla (1956-69)
Required: 2
with hub - identified by fine toothing
600 D 2. Series and 3. Series (1964-69)
Required: 2
drive shaft to stub axle shaft - identified by: coarse toothing
600 and 600 D 1. Series (1955-64) and Multipla (1956-69)
Required: 2
drive shaft to stub axle shaft - identified by: fine toothing
600 D 2. Series and 3. Series (1964-69)
Required: 2
for drive shafts with 17 and 19 mm diameter
Required: 2
for drive shaft with 19 mm diameter
Required: 2
for drive shaft with 24 mm diameter
Required: 2
drive shaft to stub axle shaft - identified by: coarse toothing
600 and 600 D 1. Series (1955-64) and Multipla (1956-69)
Required: 2
drive shaft to stub axle shaft - identified by: fine toothing
600 D 2. Series and 3. Series (1964-69)
Required: 2
drive flange to sleeve yoke
600 and 600 D 1. Series (1955-64) and Multipla (1956-69)
Required: 8
drive flange to sleeve yoke
600 D 2. Series and 3a Series (1964-69)
Required: 8
with 10 teeth and 440 mm length
600 and 600 D 1. Series (1955-64) plus Multipla (1956-69)
Required: 2
- identified by: fine toothing
600 D 2. Series and 3. Series (1964-69)
Required: 2
for drive shaft with 19 mm diameter. Identified by rotating sleeve
600 from 1955 to chassis no. 698914 and Multipla from 1956 to chassis no. 698914
Required: 2
for drive shaft with 19 mm diameter
600 from VIN...698915, Multipla from VIN...765151 and all 600 D (1960-69)
Required: 2
with aluminium bush - for drive shaft with 24 mm diameter
600 from VIN... 698915, Multipla from VIN... 765151 plus all 600 D
Required: 2
with aluminium bush - reinforced version for drive shaft with 24 mm diameter
600 from VIN... 698915, Multipla from VIN... 765151 plus all 600 D
Required: 2
with plastic bush - for drive shaft with 24 mm diameter
600 from VIN... 698915, Multipla from VIN... 765151 plus all 600 D
Required: 2
for drive shaft with 19 mm diameter
600 from VIN...698915, Multipla from VIN...765151 plus 600 D 1st series (1960-64)
Required: 2
for drive shaft with 24 mm diameter
600 D 2. Series and 3. Series (1964-69)
Required: 2
stainless steel - width: 4.6 mm, length: 150 mm, tensile strength: 46 kg
Required: 2
